manualshive.com logo in svg

Desin Instruments HS-7000 Series, General Instructions Manual

Share
Download
Desin Instruments HS-7000 Series General Instructions Manual Download Page 6

6

Please read carefully

before handling

the instrument

INTRODUCTION

CHECK PACKING CONTENTS

Should includes:

- 1 HS-7000 device.

- 2 Clamps to fix to panel (except for the converter HS-7500).

- 1 Instruction sheet.

- 3 Shunts 3,74 Ohm for mA inputs.

- 1 CJC Sensor for thermocouple Cold Junction Compensation.

Optional: In special under request models, may include:

- 1 Input Voltage Divider (for input signals greater than 75 mV).

- 1 Adapter for feedback potentiometer input.

- 1 General Instruction Manual.

- 1 CD including software and LoopWin and Proasis DCS-Win utilities.

- 1 Advanced Instruction Manual.

BASIC RECOMMENDATIONS

This Manual is addressed to the instrumentist responsible of programming and configuration and

start-up of these instruments.

NOTE:

 These instruments are provided, from factory, with protection level allowing the access

to the display parameters. The access to the submenus is protected with Passwords, to avoid
any misuse which may alter the configuration already stored in memory.

These 

INSTRUCTION MANUALS 

are continuously improved

by our publication’s department, generating updated
versions in PDF format available on our website:

 

www.desin.com

Summary of Contents for HS-7000 Series













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands