manualshive.com logo in svg

Desin Instruments HS-7000 Series, General Instructions Manual

Share
Download
Desin Instruments HS-7000 Series General Instructions Manual Download Page 23

23

DATA SHOWN ON THE HS-7300 DISPLAY IN NORMAL OPERATION

●

When customized as multi-loop Controller.

The 

HS-7300

 standard version is provided with 3 independent analog inputs AI 1, AI 2 and

AI 3 (or AI S) operating internally as Control Loops 

L1, L2 and L3

 and represented,

respectively, by the LEDs 

L1, L2 and L3.

The loops can be displayed using 

 key in any point in the MAIN MENU.

●

HS-7300. Multivariable Processor  1/8 DIN vertical format

The instrument is factory programmed as multiloop Controller. For each enabled loop will show:

-

Loop 1 (L1 On)

: The values of AI 1, SP 1 and output MV 1 of PID Loop 1.

-

Loop 2 (L2 On)

: The values of AI 1, SP 2 and output MV 2 of PID Loop 2.

-

Loop 3 (L3 On)

: The values of AI 3, SP 3 and output MV 3 of PID Loop 3.

NOTE: 

This configuration of the Menu can be modified at any time using

LoopWin software to fit the process requirements.

STANDARD MENU

The standard factory configuration provides a basic menu limited to
the SP , Auto-Manual, Alarm and Password parameters. Any other
existing configuration could has been realized under request:

- To shift the Loop press 

- To scroll the options of the menu, press 

- To go in any option, press 

- To modify the value or data of any option of the menu,

keys 

 and 

 are used.

- To exit from any option of the menu, press 

SAFETY CONDITIONS INDICATION

LED F1 flickering

, indicates that the Control Output is in Hold, due to a failure. The control

output MV (either if 4-20mA or relay output type) in this case will supply  the safety value  preset.
Thus, the Display MV of the Loop in failure, will display the safety value of the control output.

The safety Hold function is activated in the following cases:

- Input failure of this Loop

- Process Variable value exceeds the defined range.

- Feedback potentiometer signal failure in AI 3.

- Inhibit logic input of the 

[Pid]

 is activated.

For each selected Loop:

Normal Operation Display

Press 

 Direct modification of SP

Press 

 go to modify SP by digits shifting

Press 

 go to AUTO-MANU station

Press 

 go to Alarm AL 1 or AL 3 or AL 5

Press 

 go to

 

Alarm AL 2 or AL 4 or AL 6

Press 

 go to Passwords

Press 

 return to Normal Operation Display

Summary of Contents for HS-7000 Series













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands