manualshive.com logo in svg

Deprag AST40-1, Operating Instruction Booklet

Share
Download
Deprag AST40-1 Operating Instruction Booklet Download Page 34

 

34 

7.6.1.3.6 Data backup 

The command “Back up values” (Save values) can be used as frequently as required 
during the screwdriving sequence, but only the last three values will be backed up. In case 
of an error or a failure, the values are always saved. 
The value last saved is always available in the range fd_Step3 / fd_Torque3 / fd_Angle3. 
When using the "Save values" command multiple times in the screwdriver program, the 
previous values are shifted upwards (fd_Step3 

 fd_Step2 

 fd_Step1). 

If a fault occurs during a screw assembly, the screwdriving values for the incorrect step will 
be saved in the area fd_StepNOk / fd_TorqueNOk / fd_AngleNOk. 
Example: 

 

 

fd_Step3 

fd_Step3 

 fd_Step2 

fd_Step3 

fd_Step2 

 fd_Step1 

fd_Step3 

 fd_Step2 

fd_Step3 

fd_Step2 

 fd_Step1 

fd_Step3 

 fd_Step2 

fd_Step3 

fd_StepNOk 

Summary of Contents for AST40-1


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands