manualshive.com logo in svg

Deprag AST40-1, Operating Instruction Booklet

Share
Download
Deprag AST40-1 Operating Instruction Booklet Download Page 29

 

29 

interface) 

This signal indicates the status of input 4 at the hardware 
interface. 
(see 

6.2.7 I/O interfaces

) 

SysStatus INT 

System status 

This parameter indicates the system status of the AST40 – 
screwdriving controller. 
(for possible status values, see 

15.1 System error

) 

ErrorCode WORD 

Error Code 

This parameter indicates the internal errors in the module. 
(for possible errors, see below) 

Table 12: 

Data structure of the status signals (UDT22) 

 

7.6.1.3.4 Description of the – Error Code: 

Error 

Description 

FF00 

Error in the input address range 

Cause: 
The transfer parameter 

I_AddrX (X=1-4)

 is not assigned or there is a value of smaller 

or equal to 0. 

FF01 

Error while reading the input module 1 (I_Addr1) 

Possible causes: 

  An incorrect input module has been entered in the hardware configuration. Input 

module 1 must be configured with "64 bytes in". 

  Incorrect start address of the input module 1 at the interface parameter I_Addr1 

FF02 

Error while reading the input module 2 (I_Addr2) 

Possible causes: 

  An incorrect input module has been entered in the hardware configuration. Input 

module 2 must be configured with "64 bytes in". 

  Incorrect start address of the input module 2 at the interface parameter I_Addr2 

FF03 

Error while reading the input module 3 (I_Addr3) 

Possible causes: 

  An incorrect input module has been entered in the hardware configuration. Input 

module 3 must be configured with "64 bytes in". 

  Incorrect start address of the input module 3 at the interface parameter I_Addr3 

FF04 

Error while reading the input module 4 (I_Addr4) 

Possible causes: 

  An incorrect input module has been entered in the hardware configuration. Input 

module 4 must be configured with "32 bytes in". 

  Incorrect start address of the input module 4 at the interface parameter I_Addr4 

FF10 

Error in the output address range 

Cause: 
The transfer parameter 

I_AddrX (X=1-4)

 is not assigned or there is a value of smaller 

or equal to 0. 

FF11 

Error while writing to the output module 1 (O_Addr1) 

Possible causes: 

  An incorrect output module has been entered in the hardware configuration. 

Output module 1 must be configured with "64 bytes out". 

  Incorrect start address of the output module 1 at the interface parameter 

O_Addr1 

FF12 

Error while writing to the output module 2 (O_Addr2) 

Possible causes: 

Summary of Contents for AST40-1


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands