manualshive.com logo in svg

Deprag AST40-1, Operating Instruction Booklet

Share
Download
Deprag AST40-1 Operating Instruction Booklet Download Page 28

 

28 

FC_CycleDone BOOL 

Cycle ended for F-Function 
This signal is currently not available yet! 

FC_LockPart BOOL 

Lock part for F-Function 
This signal is currently not available yet! 

DataAvailable BOOL 

Data is available 

This signal indicates that new screw data is available. 
This is reset by the AST40 sequence controller, if the 
signal “Data Saved” is set by the SPS program or a new 
screwdriving sequence is started. 

Error BOOL 

Error 

This signal indicates that an error has occurred in the FB13 
module. The detailed error code is given in the "ErrorCode" 
parameter. 

HW_FC_ErrReset BOOL 

Error Reset for F-Function (hardware interface) 

This signal indicates the status of the Reset signal at the 
hardware interface. 
(see 

6.2.7 I/O interfaces

) 

HW_FC_PartSensor BOOL 

Parts sensor for F-function (hardware interface) 

This signal indicates the status of the “Parts sensor” signal 
at the hardware interface. 
(see 

6.2.7 I/O interfaces

) 

HW_FC_ReleasePart BOOL 

Part release for F-Function (hardware interface) 

This signal indicates the status of the “Part release” signal 
at the hardware interface. 
(see 

6.2.7 I/O interfaces

) 

HW_ReleaseStart BOOL 

Clearance to start (hardware interface) 

This signal indicates the status of the “Start approval” 
signal at the hardware interface. 
(see 

6.2.7 I/O interfaces

) 

HW_Start BOOL 

Start signal (Hardware interface) 

This signal indicates the status of the start signal at the 
hardware interface. 
(see 

6.2.7 I/O interfaces

) 

HW_Reload BOOL 

Reload signal (hardware interface) 

This signal indicates the status of the Reload signal at the 
hardware interface. 
(see 

6.2.7 I/O interfaces

) 

HW_ProgIn1 BOOL 

Input 1 for the screwdriver program (Hardware 
interface) 

This signal indicates the status of input 1 at the hardware 
interface. 
(see 

6.2.7 I/O interfaces

) 

HW_ProgIn2 BOOL 

Input 2 for the screwdriver program (Hardware 
interface) 

This signal indicates the status of input 2 at the hardware 
interface. 
(see 

6.2.7 I/O interfaces

) 

HW_ProgIn3 BOOL 

Input 3 for the screwdriver program (Hardware 
interface) 

This signal indicates the status of input 3 at the hardware 
interface. 
(see 

6.2.7 I/O interfaces)

 

HW_ProgIn4 BOOL 

Input 4 for the screwdriver program (Hardware 

Summary of Contents for AST40-1


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands