Delta DVS-328 series User Manual Download Page 31

Page: 31 / 246

D V S M a n a g e d I n d u s t r i a l R a c k Mo u n t E t h e r n e t S wi t c h U s e r Ma n u a l

3 - 1 0

Description

Factory default

This field displays whether the flow control is enabled for the port:



Enable

: The flow control is enabled. If the port buffers become full, the switch

sends pause packets.



Disable

: The flow control is disabled. If the port buffers become full, the switch does

not send pause packets.

Disable

Jumbo Frame

The field displays whether the jumbo frame is enabled for the port.



Enable

: The jumbo frame is enabled. The switch supports a fixed jumbo frame size

- 9000 bytes payload (9218 bytes frame) size.



Disable

: The jumbo frame is disabled.

Disable

Link Trap

Specify whether to send a trap when the interface link status changes:



Enable

: When the link status changes, the switch sends a trap. This is the default

setting.



Disable

: When the link status changes, the switch does not send a trap.

Enable

3.1.3.2

LAG Settings

You can configure the LAG settings and monitor the LAG status on this page.

LAG Settings

Description

Factory default

Port

This field shows the interface number.

interface number

Link Status

This filed shows the connection of the interface.



Link Up:

The interface is connected to another device.



Link Down:

The interface is not connected to another device.

Link Down

Admin Mode

Specify the administrative state of the interface:



Enable:

The interface is switched on and can be connected to another device.



Disable:

The interface is switched off and can not be connected to another

device.

Enable

Jumbo Frame

The filed displays whether the jumbo frame is enabled for the port.



Enable:

The jumbo frame is enabled. The switch supports a fixed jumbo

frame size - 9000 byte payload (9018 byte frame) size.



Disable:

The jumbo frame is disabled.

Disable

Link Trap

Specify whether the switch sends a trap when the interface link status changes:



Enable:

When the link status changes, the switch sends a trap. This is the

default setting.



Disable:

When the link status changes, the switch does not send a trap.

Enable

Summary of Contents for DVS-328 series























































































































































































































































Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands

Delta DVS-328 series, User Manual

Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands