Delta DVS-328 series User Manual Download Page 72 | Manualshive

Page: 72 / 246

background image

C h a p t e r 3 F e a t u r e d F u n c t i o n s

3 - 5 1



Backup Port:

The backup port of designated ports. When a designated port is blocked, the backup port

becomes a new designated port and starts to forward data without delay. When a loop occurs while two
ports of the same MSTP device are interconnected, the device will block either of the two ports, and the
backup port is the port to be blocked.

CST Port Status

Item

Description

Interface

The interface number or port channel number.

Port ID

The port identifier for the interface within the CST, which consists of the port
priority and the interface number.

Port Forwarding State

The forwarding state of the interface. One of the following options is displayed:



Discarding:

The interface is in the discarding mode; it can not forward traffic

and can not learn new MAC addresses.



Learning:

The interface is in the learning mode; it can not forward traffic, but

it can learn new MAC addresses.



Forwarding:

The interface is in the forwarding mode; it can forward traffic

and learn new MAC addresses.

«
...
70
71
72
73
74
...
»

Summary of Contents for DVS-328 series























































































































































































































































Reviews:

No comments

Related manuals for DVS-328 series

Brand: G-Technology Pages: 35

Brand: Ubiquiti Pages: 3

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

Brand: insys icom Pages: 4

Brand: Lantech Pages: 40

Brand: BHU NETWORKS Pages: 75

ipRocketLink 3086FR

Brand: Patton electronics Pages: 12

Brand: Aaeon Pages: 57

Brand: Juniper Pages: 196

Brand: Black Box Pages: 12

AGENT-2 S41D Line

Brand: Pullnet Pages: 89

airPoint Nexus sB3210

Brand: SmartBridges Pages: 55

Brand: ActionTec MI424WR Pages: 3

Brand: Erbauer Pages: 36

Brand: Comtrend Corporation Pages: 208

Brand: Dynamix Pages: 87

Brand: MAKER MADE Pages: 40

TeleLite 720920 Series

Brand: Positron Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands