Delta DVS-328 series User Manual Download Page 113 | Manualshive

Page: 113 / 246

background image

D V S M a n a g e d I n d u s t r i a l R a c k Mo u n t E t h e r n e t S wi t c h U s e r Ma n u a l

3 - 9 2

802.1X Basic Settings

Description

Factory default

System Control

Specify whether the 802.1X authentication module on the switch is running or shut
down.



Shutdown:

The 802.1X authentication is shut down. You can not configure or

enable the 802.1X authentication.



Start:

The 802.1X authentication is running, and you can configure and enable it.

Start

802.1X Authentication

Specify the status of the 802.1X authentication on the switch.



Disable:

The 802.1X authentication is disabled. You can still configure the 802.1X

authentication, but the settings do not take effect after you have applied them. The
switch does not check the 802.1X authentication before allowing traffic on any
interfaces, even if the interfaces are configured to allow only authenticated users.



Enable:

The 802.1X authentication is enabled. You can configure the 802.1x

authentication, and the settings take effect after you have applied them.

Enable

Authentication Mode

Specify the 802.1X authentication mode.



Local:

A locally stored user ID and password are used for port authentication. You

need to set up a user account on the Local Authentication Server page. This is the
default setting.



Remote:

A RADIUS or server is used for the port authentication. With

this selection, the Remote Authentication Server Type radio buttons and Network
Access Server ID become available.

Local

Remote Authentication Server Type

If you select the Remote mode of Authentication Mode, specify whether a RADIUS or
server should be used.



:

The user ID and the password are authenticated through a

server.



RADIUS:

The user ID and the password are authenticated through a RADIUS

server.

RADIUS

Network Access Server ID

If you select the Remote radio button next to Authentication Mode, enter the network
access server (NAS) ID, or use the default ID (fsNas1).

Fixed

Port Authentication

You can configure the authentication settings for each interface.

«
...
111
112
113
114
115
...
»

Summary of Contents for DVS-328 series























































































































































































































































Reviews:

No comments

Related manuals for DVS-328 series

Brand: Garmin Pages: 2

Brand: D-Link Pages: 213

ZyXEL EES-1024AF

Brand: ZyXEL Communications Pages: 99

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: Ubiquiti Pages: 20

Brand: AMG Systems Pages: 2

Brand: QUNDIS Pages: 42

Brand: LevelOne Pages: 3

Brand: Zhone Pages: 28

HFisolator 9730/26-11

Brand: Stahl Pages: 2

netHOST NHST-T100

Brand: hilscher Pages: 75

Air Live GW-300R

Brand: Ovislink Pages: 20

EZ Switch SMC-EZ1024FDT

Brand: SMC Networks Pages: 4

Monochrome Image Acquisition Device NI 1410

Brand: National Instruments Pages: 34

Brand: Net Optics Pages: 2

Brand: Paradyne Pages: 216

Brand: Hama Pages: 45

Brand: Digi Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands