Delta DVS-328 series User Manual Download Page 208

Page: 208 / 246

D V S S e r i e s M a n a g e d E t h e r n e t S w i t c h U s e r M a n u a l

C - 8

Attr ID

Access rule

Name

Data type

Description of attribute

Get

In Unknown Protos

UDINT

Inbound packets with unknown
protocol

Out Octets

UDINT

Octets sent on the interface

Out Ucast Packets

UDINT

Unicast packets sent on the interface

Out Nucast Packets

UDINT

Non-unicast packets sent on the
interface

Out Discards

UDINT

Outbound packets discarded

Out Errors

UDINT

Outbound packets that contain errors

Get

Media Counters

STRUCT of:

Media-specific counters

Alignment Errors

UDINT

Frames received that are not an
integral number of octets in length

FCS Errors

UDINT

Frames received that do not pass the
FCS check

Single Collisions

UDINT

Successfully transmitted frames
which experienced exactly one
collision

Multiple Collisions

UDINT

Successfully transmitted frames
which experienced more than one
collision

SQE Test Errors

UDINT

Number of times SQE test error
message is generated

Deferred
Transmissions

UDINT

Frames for which first transmission
attempt is delayed because the
medium is busy

Late Collisions

UDINT

Number of times a collision is detected
later than 512 bit-times into the
transmission of a packet

Excessive Collisions UDINT

Frames for which transmission fails
due to excessive collisions

MAC Transmit Errors UDINT

Frames for which transmission fails
due to an internal MAC sublayer
transmit error

Carrier Sense Errors UDINT

Times that the carrier sense condition
was lost or never asserted when
attempting to transmit a frame

Frame Too Long

UDINT

Frames received that exceed the
maximum permitted frame size

MAC Receive Errors UDINT

Frames for which reception on an
interface fails due to an internal MAC
sublayer receive error

Get

Interface Label

SHORT_STRING

Human readable identification

Common Services

Service

Code

Need in Implementation

Service name

Description of Service

Class

Instance

0x0E

Get_Attribute_Single

Returns the contents of the specified
attribute.

Base Switch Object (0x51)

Class Attributes

Attr ID

Access rule

Name

Data type

Description of attribute

Get

Revision

UINT

Revision of this object. The current
value assigned to this values is 1

Summary of Contents for DVS-328 series























































































































































































































































Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands

Delta DVS-328 series, User Manual

Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands