Delta DVS-328 series User Manual Download Page 149 | Manualshive

Page: 149 / 246

background image

D V S M a n a g e d I n d u s t r i a l R a c k Mo u n t E t h e r n e t S wi t c h U s e r Ma n u a l

3 - 1 2 8

Multiple Port Mirroring

Description

Factory default

Monitored Port

Specify the monitored port or ports for the monitoring.

Unchecked

Session Mode

Specify whether the port mirroring session mode is enabled:



Enable:

The port mirroring is enabled. The setting applies to all interfaces.



Disable:

The port mirroring is disabled. The setting applies to all interfaces.

Note:

When you configure the session mode for an individual interface, it is
applied to all interfaces. You can select

Enable

from the Session Mode

drop-down list and control the port mirroring for individual interfaces. If you
want to disable the port mirroring, make sure that the direction is not
configured for the interfaces. If the direction is configured for the interfaces
and you want to disable the port mirroring, select the check box of the
interface, and click

Delete

to remove the port mirroring configuration for the

interface.

None

Watch Direction

Specify the direction in which the port mirroring occurs:



Tx and Rx:

Both outgoing traffic and incoming traffic are mirrored.



Tx Only:

Only outgoing traffic is mirrored.



Rx Only:

Only incoming traffic is mirrored.

None

Mirror Port

Specify the port which is the mirror port.

None

Status Table

Item

Description

Monitored Port

This field displays the monitored port number.

Mirror Port

This field displays the destination port or the monitored interface. Only one port
can be the mirror port. This port is used as the mirror port for all ports which you
configure for the port mirroring.

Session Mode

The port mirroring status of the port.



Enable:

The port mirroring is enabled.



Disable:

The port mirroring is disabled.

Direction

The direction of the port mirroring.



Tx and Rx:

Both outgoing traffic and incoming traffic are mirrored.



Tx Only:

Only outgoing traffic is mirrored.



Rx Only:

Only incoming traffic is mirrored.

«
...
147
148
149
150
151
...
»

Summary of Contents for DVS-328 series























































































































































































































































Reviews:

No comments

Related manuals for DVS-328 series

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: Watchguard Pages: 24

3C13886 - Router OC-3 ATM SML Flexible Interface...

Brand: 3Com Pages: 171

OfficeConnect WX2200

Brand: 3Com Pages: 204

Brand: NETGEAR Pages: 169

Brand: TP-Link Pages: 2

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

SINUS H PROFInet

Brand: Enertronica Santerno Pages: 34

Brand: Xantech Pages: 4

E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010

Brand: Juniper Pages: 122

Brand: JUMO Pages: 60

Brand: Avaya Pages: 73

Brand: Idis Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands