Delta DVS-328 series User Manual Download Page 53

Page: 53 / 246

D V S M a n a g e d I n d u s t r i a l R a c k Mo u n t E t h e r n e t S wi t c h U s e r Ma n u a l

3 - 3 2

SSH Configuration

Description

Factory default

SSH Admin Mode

Specify the status of SSH.



Disable

: SSH is disabled. This is the default setting.



Enable

: SSH is enabled.

Disable

SSH Version 1

Specify whether SSH version 1 is supported.



Disable

: SSH version 1 is not supported.



Enable

: SSH version 1 is supported. Both version 1 and version 2 can be

supported on the switch.

Enable

SSH Version 2

Specify whether SSH version 2 is supported.



Disable

: SSH version 2 is not supported.



Enable

: SSH version 2 is supported. Both version 1 and version 2 can be

supported on the switch.

Enable

SSH Session Timeout (minutes)

The SSH session timeout period in minutes. When there is no activity and the
timeout period is reached, the SSH session will be closed. Enter a period in the
range of 1 to 160 minutes.

Maximum Number of SSH Sessions

The maximum number of inbound SSH sessions. The number must be in the range
of 0 to 5.

Current Number of SSH Sessions

This field displays the number of simultaneous SSH sessions.

3.1.8.4

Telnet Configuration

You can configure the Telnet configuration on this page.

Summary of Contents for DVS-328 series























































































































































































































































Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands

Delta DVS-328 series, User Manual

Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands