Delta DVS-328 series User Manual Download Page 65

Page: 65 / 246

D V S M a n a g e d I n d u s t r i a l R a c k Mo u n t E t h e r n e t S wi t c h U s e r Ma n u a l

3 - 4 4

3.3.1.1

STP Configuration

Global Settings Description

Description

Factory default

Spanning Tree Admin Mode

Specify the admin mode of STP on the switch:



Disable:

STP is disabled. The settings do not take effect after you have applied

them, but you still can configure STP.



Enable:

STP is enabled. The settings take effect after you have applied them.

Enable

Force Protocol Version

Specify the version of the STP protocol:



STP:

Spanning Tree Protocol.



RSTP:

Rapid Spanning Tree Protocol.



MSTP:

Multiple Spanning Tree Protocol.

MSTP

Configuration Name

Enter the STP identifier for the switch. You can configure alphanumeric characters
and special characters, and the maximum length is 32.

MAC address of

the switch

Configuration Revision Level

Enter an identifier that specifies the current configuration. The number must be in the
range of 0 to 65535.

Forward BPDU while STP Disabled

Specify whether spanning tree bridge protocol data units (BPDUs) are forwarded:



Disable:

When STP is disabled, Spanning tree BPDUs are not forwarded.



Enable:

When STP is disabled, Spanning tree BPDUs are forwarded.

Disable

Configuration Digest Key

This field displays a calculated value from the MSTP configuration. The switches are
qualified by the key and the function in the same region.

Fixed

Configuration Format Selector

This field displays the configuration identifier format selector that is used.

Summary of Contents for DVS-328 series























































































































































































































































Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands

Delta DVS-328 series, User Manual

Search results

Summary of Contents for DVS-328 series

Reviews:

Related manuals for DVS-328 series

Brands by name

Popular brands