Dell S3048-ON Configuration Manual Download Page 896

Page: 896 / 1036

The advantages of syncing the multicast routes between VLT peers are:

•

VLT resiliency

— After a VLT link or peer failure, if the traffic hashes to the VLT peer, the traffic continues to be routed using multicast

until the PIM protocol detects the failure and adjusts the multicast distribution tree.

•

Optimal routing

— The VLT peer that receives the incoming traffic can directly route traffic to all downstream routers connected on

VLT ports.

•

Optimal VLTi forwarding

— Only one copy of the incoming multicast traffic is sent on the VLTi for routing or forwarding to any orphan

ports, rather than forwarding all the routed copies.

Important Points to Remember

•

You can only use one spanned VLAN from a PIM-enabled VLT node to an external neighboring PIM router.

•

If you connect multiple spanned VLANs to a PIM neighbor, or if both spanned and non-spanned VLANs can access the PIM neighbor,

ECMP can cause the PIM protocol running on each VLT peer node to choose a different VLAN or IP route to reach the PIM neighbor.

This can result in issues with multicast route syncing between peers.

•

Both VLT peers require symmetric Layer 2 and Layer 3 configurations on both VLT peers for any spanned VLAN.

•

For optimal performance, configure the VLT VLAN routing metrics to prefer VLT VLAN interfaces over non-VLT VLAN interfaces.

•

When using factory default settings on a new switch deployed as a VLT node, packet loss may occur due to the requirement that all

ports must be open.

•

ECMP is not compatible on VLT nodes using VLT multicast. You must use a single VLAN.

Configuring VLT Multicast

To enable and configure VLT multicast, follow these steps.

Enable VLT on a switch, then configure a VLT domain and enter VLT-domain configuration mode.
CONFIGURATION mode

vlt domain

domain-id

Enable peer-routing.
VLT DOMAIN mode

peer-routing

Configure the multicast peer-routing timeout.
VLT DOMAIN mode

multicast peer-routing—timeout

value

: Specify a value (in seconds) from 1 to 1200.

Configure a PIM-SM compatible VLT node as a designated router (DR). For more information, refer to

Configuring a Designated

Router

Configure a PIM-enabled external neighboring router as a rendezvous point (RP). For more information, refer to

Configuring a Static

Rendezvous Point

Configure the VLT VLAN routing metrics to prefer VLT VLAN interfaces over non-VLT VLAN interfaces. For more information, refer to

Classify Traffic

Configure symmetrical Layer 2 and Layer 3 configurations on both VLT peers for any spanned VLAN.

Non-VLT ARP Sync

ARP entries (including ND entries) learned on other ports are synced with the VLT peer to support station move scenarios.

NOTE:

ARP entries learned on non-VLT, non-spanned VLANs are not synced with VLT peers.

896

Virtual Link Trunking (VLT)

Summary of Contents for S3048-ON













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for S3048-ON

Reviews:

Related manuals for S3048-ON

Brands by name

Popular brands

Dell S3048-ON, Configuration Manual

Search results

Summary of Contents for S3048-ON

Reviews:

Related manuals for S3048-ON

Brands by name

Popular brands