To configure simple authentication, use the following command.
•
Configure a simple text password.
INTERFACE-VRID mode
authentication-type simple [
encryption-type
]
password
Parameters:
•
encryption-type
:
0
indicates unencrypted;
7
indicates encrypted.
•
password
: plain text.
Examples of the
authentication-type
Command
The bold section shows the encryption type (encrypted) and the password.
Dell(conf-if-gi-1/1-vrid-111)#authentication-type ?
Dell(conf-if-gi-1/1-vrid-111)#authentication-type
simple 7 force10
The following example shows verifying the VRRP authentication configuration using the
show conf
command. The bold section shows
the encrypted password.
Dell(conf-if-gi-1/1-vrid-111)#show conf
!
vrrp-group 111
authentication-type simple 7
387a7f2df5969da4
priority 255
virtual-address 10.10.10.1
virtual-address 10.10.10.2
virtual-address 10.10.10.3
virtual-address 10.10.10.10
Disabling Preempt
The
preempt
command is enabled by default. The command forces the system to change the MASTER router if another router with a
higher priority comes online.
Prevent the BACKUP router with the higher priority from becoming the MASTER router by disabling preempt.
NOTE:
You must configure all virtual routers in the VRRP group the same: you must configure all with preempt enabled or
configure all with preempt disabled.
Because preempt is enabled by default, disable the preempt function with the following command.
•
Prevent any BACKUP router with a higher priority from becoming the MASTER router.
INTERFACE-VRID mode
no preempt
Examples of Disabling Preempt
Re-enable preempt by entering the
preempt
command. When you enable preempt, it does not display in the
show
commands, because it
is a default setting.
The following example shows how to disable preempt using the
no preempt
command.
Dell(conf-if-gi-1/1)#vrrp-group 111
Dell(conf-if-gi-1/1-vrid-111)#no preempt
Dell(conf-if-gi-1/1-vrid-111)#
The following example shows how to verify preempt is disabled using the
show conf
command.
Dell(conf-if-gi-1/1-vrid-111)#show conf
!
vrrp-group 111
authentication-type simple 7 387a7f2df5969da4
Virtual Router Redundancy Protocol (VRRP)
981
Summary of Contents for S3048-ON
