4
Implement a
wide metric-style
globally.
ROUTER ISIS AF IPV6 mode
isis ipv6 metric metric-value [level-1 | level-2 | level-1-2]
To configure wide or wide transition metric style, the cost can be between 0 and 16,777,215.
Configuring IS-IS Graceful Restart
To enable IS-IS graceful restart globally, use the following commands. Additionally, you can implement optional commands to enable the
graceful restart settings.
•
Enable graceful restart on ISIS processes.
ROUTER-ISIS mode
graceful-restart ietf
•
Configure the time during which the graceful restart attempt is prevented.
ROUTER-ISIS mode
graceful-restart interval
minutes
The range is from 1 to 120 minutes.
The default is
5 minutes
.
•
Enable the graceful restart maximum wait time before a restarting peer comes up.
ROUTER-ISIS mode
graceful-restart restart-wait
seconds
When implementing this command, be sure to set the t3 timer to adjacency on the restarting router.
The range is from 1 to 120 minutes.
The default is
30 seconds
.
•
Configure the time that the graceful restart timer T1 defines for a restarting router to use for each interface, as an interval before
regenerating Restart Request (an IIH with RR bit set in Restart TLV) after waiting for an acknowledgement.
ROUTER-ISIS mode
graceful-restart t1 {interval
seconds
| retry-times
value
}
•
interval
: wait time (the range is from 5 to 120. The default is
5
.)
•
retry-times
: number of times an unacknowledged restart request is sent before the restarting router gives up the graceful
restart engagement with the neighbor. (The range is from 1 to 10 attempts. The default is
1
.)
•
Configure the time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize.
ROUTER-ISIS mode
graceful-restart t2 {level-1 | level-2}
seconds
•
level-1
,
level-2
: identifies the database instance type to which the wait interval applies.
The range is from 5 to 120 seconds.
The default is
30 seconds
.
•
Configure graceful restart timer T3 to set the time used by the restarting router as an overall maximum time to wait for database
synchronization to complete.
ROUTER-ISIS mode
graceful-restart t3 {adjacency | manual
seconds
}
404
Intermediate System to Intermediate System
Summary of Contents for S3048-ON
