•
local-AS
: routes with the COMMUNITY attribute of NO_EXPORT_SUBCONFED.
•
no-advertise
: routes with the COMMUNITY attribute of NO_ADVERTISE.
•
no-export
: routes with the COMMUNITY attribute of NO_EXPORT.
•
quote-regexp
: then any number of regular expressions. The software applies all regular expressions in the list.
•
regexp
: then a regular expression.
Example of the
show ip community-lists
Command
To view the configuration, use the
show config
command in CONFIGURATION COMMUNITY-LIST or CONFIGURATION
EXTCOMMUNITY LIST mode or the
show ip {
community-lists
|
extcommunity-list
}
command in EXEC Privilege mode.
Dell#show ip community-lists
ip community-list standard 1
deny 701:20
deny 702:20
deny 703:20
deny 704:20
deny 705:20
deny 14551:20
deny 701:112
deny 702:112
deny 703:112
deny 704:112
deny 705:112
deny 14551:112
deny 701:667
deny 702:667
deny 703:667
deny 704:666
deny 705:666
deny 14551:666
Dell#
Configuring an IP Extended Community List
To configure an IP extended community list, use these commands.
1
Create a extended community list and enter the EXTCOMMUNITY-LIST mode.
CONFIGURATION mode
ip extcommunity-list
extcommunity-list-name
2
Two types of extended communities are supported.
CONFIG-COMMUNITY-LIST mode
{permit | deny} {{rt | soo} {
ASN:NN
|
IPADDR:N
} | regex
REGEX-LINE
}
Filter routes based on the type of extended communities they carry using one of the following keywords:
•
rt
: route target.
•
soo
: route origin or site-of-origin. Support for matching extended communities against regular expression is also supported. Match
against a regular expression using the following keyword.
•
regexp
: regular expression.
Example of the
show ip extcommunity-lists
Command
To set or modify an extended community attribute, use the
set extcommunity {rt | soo} {ASN:NN | IPADDR:NN}
command.
To view the configuration, use the
show config
command in CONFIGURATION COMMUNITY-LIST or CONFIGURATION
EXTCOMMUNITY LIST mode or the
show ip {
community-lists
|
extcommunity-list
}
command in EXEC Privilege mode.
Dell#show ip community-lists
ip community-list standard 1
200
Border Gateway Protocol IPv4 (BGPv4)
Summary of Contents for S3048-ON
