manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 264

chassis

component serial number labels...........................188
front view.............................................................................4
lifting warnings and guidelines................................214
physical specifications..............................................4,  9
rear view...............................................................................5
slot numbering.................................................................14
status LEDs.......................................................................24

checklist for site preparation..............................................63
clearance requirements........................................................73
clip nuts

See

cage nuts

compliance

acoustic noise...............................................................242
Canadian EMC..............................................................240
declarations of conformity.......................................243
EMC requirements......................................................240
European EMC...............................................................241
FCC EMC..........................................................................241
general standards.......................................................239
Japanese EMC...............................................................241
lithium battery..............................................................220
NEBS.................................................................................242
United States EMC.......................................................241

components, switch

descriptions.......................................................................19
hardware, for redundancy............................................12
installation overview....................................................113
inventory...........................................................................101
packing for shipping....................................................196
packing line cards for shipping................................197
power requirements......................................................82
serial number label......................................................188
specifications..................................................................49

configuration................................................................................7

factory default...............................................................143
initial (CLI)......................................................................144
initial (J-Web)................................................................146

conformity declarations.....................................................243
console port

pinouts...............................................................................49

contacting Dell.......................................................................187
conventions, documentation.............................................xiv
cooling system.........................................................................44

overview...............................................................................6

See also

airflow

customer support...........................................................xv, 183

D

declarations of conformity...............................................243

default configuration...........................................................143
Dell automated order-status service............................185
Dell Enterprise Training and Certification....................185
Dell online services...............................................................184
Dell product information....................................................185
Dell Support............................................................................183
Dell support service, contacting......................................185
Dell, contacting......................................................................187
depth, chassis.............................................................................9
diagnostic checklist.............................................................186
dispersion in fiber-optic cables.........................................78
documentation conventions..............................................xiv
downloading software..........................................................xiv

E

e-mail addresses, Dell........................................................184
earth ground, connecting...................................................129
earthquakes, tested toleration for shock......................66
electricity

warnings and guidelines...........................................229

See also

power

wiring guidelines.............................................................65

EMC (electromagnetic compatibility)

preventing problems with..........................................66
requirements.................................................................240
standards.......................................................................239

EMI (electromagnetic interference)

standards.......................................................................239
suppressing......................................................................66

environmental requirements and

specifications......................................................................66

environmental specifications............................................66
ESD wrist strap

usage................................................................................230
verifying resistance, for safety.................................231

EU Declaration of Conformity..........................................243
European EMC compliance...............................................241
European Union Declaration of Conformity...............243

F

factory default configuration............................................143
fan tray

illustration.........................................................................45
installation.......................................................................116
removal............................................................................159
serial number location.................................................191

FCC EMC compliance..........................................................241

248

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands