manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 143

CAUTION:

Before you slide the transceiver into the port, ensure the

transceiver is aligned correctly. Misalignment might cause the pins to
bend, making the transceiver unusable.

5.

Slide the transceiver in gently until it is fully seated.

6.

Remove the rubber safety cap when you are ready to connect the cable to the
transceiver.

WARNING:

Do not look directly into a fiber-optic transceiver or into the

ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cables
connected to transceivers emit laser light that can damage your eyes.

Figure 55: Installing a Transceiver in a J-EX Series Switch

Related

Documentation

Removing a Transceiver from a J-EX Series Switch on page 168

•

•

Connecting a Fiber-Optic Cable to a J-EX Series Switch on page 127

•

Optical Interface Support in J-EX8200 Switches on page 51

Connecting a Fiber-Optic Cable to a J-EX Series Switch

J-EX Series switches have field-replaceable unit (FRU) optical transceivers to which you
can connect fiber-optic cables.

Before you begin connecting a fiber-optic cable to an optical transceiver installed in a
J-EX Series switch, ensure that you have taken the necessary precautions for safe handling
of lasers (see “Laser and LED Safety Guidelines and Warnings for J-EX Series Switches”
on page 207).

127

Chapter 9: Installing Switch Components

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands