manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 200

When prompted by Dell's automated telephone system, enter your Express Service Code
to route the call directly to the proper support personnel. For instructions on using the
Dell Support, see “Support Service” on page 185.

NOTE:

Some of the following services are not always available in all locations

outside the continental U.S. Call your local Dell representative for information
on availability.

Online Services

You can learn about Dell products and services on the following websites:

•

http://www.dell.com

•

http://www.dell.com/ap

(Asian/Pacific countries only)

•

http://www.dell.com/jp

(Japan only)

•

http://www.euro.dell.com

(Europe only)

•

http://www.dell.com/la

(Latin American and Caribbean countries)

•

http://www.dell.ca

(Canada only)

You can access Dell Support through the following websites and e-mail addresses:

•

Dell Support websites

•

http://www.support.dell.com

•

http://support.jp.dell.com

(Japan only)

•

http://support.euro.dell.com

(Europe only)

•

Dell Support e-mail addresses

•

[email protected]

•

[email protected]

•

[email protected]

(Latin America and Caribbean countries only)

•

[email protected]

(Asian/Pacific countries only)

•

Dell Marketing and Sales e-mail addresses

•

[email protected]

(Asian/Pacific countries only)

•

[email protected]

(Canada only)

•

Anonymous file transfer protocol (FTP)

•

ftp://ftp.dell.com

Log in as

user: anonymous

, and use your e-mail address as your password.

184

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands