manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 218

•

Replace fuses only with fuses of the same type and rating.

•

Do not open or remove chassis covers or sheet-metal parts unless instructions are
provided in the hardware documentation for this product. Such an action could cause
severe electrical shock.

•

Do not push or force any objects through any opening in the chassis frame. Such an
action could result in electrical shock or fire.

•

Avoid spilling liquid onto the J-EX Series switch chassis or onto any switch component.
Such an action could cause electrical shock or damage the switch.

•

Avoid touching uninsulated electrical wires or terminals that have not been
disconnected from their power source. Such an action could cause electrical shock.

•

Always ensure that all modules, power supplies, and cover panels are fully inserted
and that the installation screws are fully tightened.

Related

Documentation

AC Power Electrical Safety Guidelines for J-EX Series Switches on page 232

•

•

General Electrical Safety Guidelines and Warnings for J-EX Series Switches on page 229

•

Maintenance and Operational Safety Guidelines and Warnings for J-EX Series Switches
on page 220

•

Laser and LED Safety Guidelines and Warnings for J-EX Series Switches on page 207

•

Installation Instructions Warning for J-EX Series Switches on page 213

•

Grounded Equipment Warning for J-EX Series Switches on page 219

Definitions of Safety Warning Levels for J-EX Series Switches

The documentation for J-EX Series switches uses the following levels of safety warnings
(there are two “Warning” formats):

NOTE:

You might find this information helpful in a particular situation, or you

might overlook this important information if it was not highlighted in a Note.

CAUTION:

You need to observe the specified guidelines to avoid minor injury

or discomfort to you or severe damage to the J-EX Series switch.

WARNING:

This symbol alerts you to the risk of personal injury from a laser.

WARNING:

This symbol means danger. You are in a situation that could cause

bodily injury. Before you work on any equipment, be aware of the hazards

202

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands