manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 161

•

Stop Bits—1

•

DCD State—Disregard

To connect and configure the switch from the console:

1.

Connect the console port to a laptop or PC using the RJ-45 to DB-9 serial port adapter.
The RJ-45 cable and RJ-45 to DB-9 serial port adapter are supplied with the switch.

The console port is located on the Routing Engine (RE) module in slot RE0 in a
J-EX8216 switch.

2.

At the Junos OS shell prompt

root%

, type

ezsetup

.

3.

Enter the hostname. This is optional.

4.

Enter the root password you plan to use for this device. You are prompted to re-enter
the root password.

5.

Enter

yes

to enable services like Telnet and SSH. By default, Telnet is not enabled and

SSH is enabled.

NOTE:

When Telnet is enabled, you will not be able to log in to a J-EX

Series switch through Telnet using

root

credentials. Root login is allowed

only for SSH access.

6.

Use the Management Options page to select the management scenario—

Configure

out-of-band management

. Specify the IP address and gateway of the management

interface. Use this IP address to connect to the switch.

NOTE:

On J-EX8200 switches, only the out-of-band management option

is available.

7.

Specify the SNMP Read Community, Location, and Contact to configure SNMP
parameters. These parameters are optional.

8.

Specify the system date and time. Select the time zone from the list. These options
are optional.

The configured parameters are displayed. Enter

yes

to commit the configuration.

The configuration is committed as the active configuration for the switch. You can now
log in with the CLI or the J-Web interface to continue configuring the switch. If you use
the J-Web interface to continue configuring the switch, the Web session is redirected to
the new management IP address. If the connection cannot be made, the J-Web interface
displays instructions for starting a J-Web session.

Related

Documentation

Connecting and Configuring a J-EX Series Switch (J-Web Procedure) on page 146

•

•

Installing and Connecting a J-EX8216 Switch on page 97

145

Chapter 11: Performing Initial Configuration

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands