Dell PowerConnect J-8216 Hardware Manual Download Page 52

Page: 52 / 270

Figure 20: Status LEDs on 48-port RJ-45 Line Card

Table 18 on page 36 describes the status LEDs on line cards for the J-EX8200 switch,
their colors and state, and the status they indicate.

Table 18: Status LEDs on Line Cards for J-EX8200 Switches

State and Description

Color

LED

The line card is enabled/online.

Green

The line card is disabled/offline.

Yellow

There is no power being supplied to the line card.

Unlit

•

On steadily—The line card is functioning normally.

•

Blinking—The line card is booting.

Green

•

On steadily—There is a line card failure or alarm.

•

Blinking—The line card is in diagnostic mode.

Yellow

The line card is disabled/offline.

Unlit

Documentation

8-port SFP+ Line Card in a J-EX8200 Switch on page 32

•

48-port SFP Line Card in a J-EX8200 Switch on page 33

•

48-port RJ-45 Line Card in a J-EX8200 Switch on page 34

•

Network Port LEDs in a J-EX8200 Switch on page 36

Network Port LEDs in a J-EX8200 Switch

Each network port on the faceplate of a line card in a J-EX8200 switch has two LEDs.

Figure 21 on page 37 shows the network port LEDs on an 8-port SFP+ line card.

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Search results

Summary of Contents for PowerConnect J-8216

Reviews:

Brands by name

Popular brands

Dell PowerConnect J-8216, Hardware Manual

Search results

Summary of Contents for PowerConnect J-8216

Reviews:

Brands by name

Popular brands