manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 175

Figure 71: Removing an AC Power Supply from a J-EX8200 Switch

Related

Documentation

Installing an AC Power Supply in a J-EX8200 Switch on page 114

•

•

AC Power Supply in a J-EX8200 Switch on page 39

Removing a Fan Tray from a J-EX8216 Switch

A J-EX8216 switch has two field-replaceable fan trays. Both fan trays are hot-removable
and hot-insertable field-replaceable units (FRUs); you can remove and replace the fan
tray while the switch is running without turning off power to the switch or disrupting
switching functions.

CAUTION:

Do not remove the fan tray unless you have a replacement fan

tray available.

Both fan trays install vertically on the left front of the chassis. Handles on the front
faceplate of each fan tray facilitate handling of the fan trays. There is a spring-loaded
latch on the base of each fan tray that is used to latch the fan tray into the chassis.

Before you remove a fan tray:

•

Ensure you understand how to prevent ESD damage. See “Prevention of Electrostatic
Discharge Damage on J-EX Series Switches” on page 230.

Ensure that you have the following parts and tools available to remove a fan tray from
a J-EX8216 switch chassis:

•

Electrostatic discharge (ESD) grounding strap

•

Replacement fan tray

159

Chapter 13: Removing Switch Components

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands