manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 144

To connect a fiber-optic cable to an optical transceiver installed in a J-EX Series switch:

WARNING:

Do not look directly into a fiber-optic transceiver or into the ends

of fiber-optic cables. Fiber-optic transceivers and fiber-optic cables connected
to transceivers emit laser light that can damage your eyes.

1.

If the fiber-optic cable connector is covered by a rubber safety cap, remove the cap.
Save the cap.

2.

Remove the rubber safety cap from the optical transceiver. Save the cap.

3.

Insert the cable connector into the optical transceiver (see Figure 56 on page 128).

Figure 56: Connecting a Fiber-Optic Cable to an Optical Transceiver
Installed in a J-EX Series Switch

g027016

Fiber-optic cable

Transceiver

4.

Secure the cables so that they are not supporting their own weight. Place excess cable
out of the way in a neatly coiled loop. Placing fasteners on a loop helps cables maintain
their shape.

CAUTION:

Do not bend fiber-optic cables beyond their minimum bend

radius. An arc smaller than a few inches in diameter can damage the cables
and cause problems that are difficult to diagnose.

Do not let fiber-optic cables hang free from the connector. Do not allow
fastened loops of cables to dangle, which stresses the cables at the
fastening point.

Related

Documentation

Disconnecting a Fiber-Optic Cable from a J-EX Series Switch on page 170

•

•

Installing a Transceiver in a J-EX Series Switch on page 126

•

Maintaining Fiber-Optic Cables in J-EX Series Switches on page 179

•

Optical Interface Support in J-EX8200 Switches on page 51

128

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands