manualshive.com logo in svg

Dell PowerConnect J-8216, Hardware Manual

Share
Download
Dell PowerConnect J-8216 Hardware Manual Download Page 60

NOTE:

If the

INPUT OK

LED and the

OUTPUT OK

LED are unlit, the AC power

cord is not installed properly or the power supply has failed.

If the

INPUT OK

LED is lit and the

OUTPUT OK

LED is unlit, the AC power

supply is not installed properly or the power supply has an internal failure.

If the

FAIL

LED is lit, the power supply has failed and must be replaced. If the

FAIL

LED is blinking, add a power supply to balance the power demand and

supply.

Related

Documentation

AC Power Specifications for J-EX8200 Switches on page 81

•

•

Power Requirements for J-EX8216 Switch Components on page 82

•

AC Power Cord Specifications for a J-EX8200 Switch on page 83

•

Connecting AC Power to a J-EX8200 Switch on page 131

Cooling System and Airflow in a J-EX8216 Switch

The cooling system in a J-EX8216 switch consists of two fan trays. Each fan tray has nine
fans and two fan tray controllers. The fan trays are hot-insertable and hot-removable
field-replaceable units (FRUs).

Both fan trays install vertically on the front of the chassis, one on the top left and the
other on the bottom left. Each fan tray has a handle on the front faceplate that facilitates
handling of the fan tray. See Figure 27 on page 45.

44

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Summary of Contents for PowerConnect J-8216















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands