Datex-Ohmeda 7100 Technical Reference Manual Download Page 128

Page: 128 / 158

7100 Anesthesia Ventilator

7-22

02/03 1006-0836-000

To replace

the power cord/harness

1. Remove the top shroud (

) (refer to Aestiva Machine Service Manual).

2. Remove the harness connector (

) from mounting bracket.

3. Disconnect the ground wires (

4. Disconnect the wires from the Tec 6 outlet (

5. Disconnect the power cord from the control module (

For machines with Display Arm

, disassemble arm to gain access to

routing for power cord

•

Remove cover at end of arm.

•

Remove top cover of arm.

•

Remove front and back plates from shoulder.

•

Loosen shoulder mounting screws enough to form gap at top large
enough to pass the power plug connector.

For machines with Folding Mount

, remove the side panel.

7. Pull the power cord into the electrical enclosure.

8. Reassemble in reverse order.

9. Apply

RTV

where the cord enters the machine area from the top.

RTV

Folding
Mount

A R M

Summary of Contents for 7100






























































































































































Search results

Summary of Contents for 7100

Reviews:

Related manuals for 7100

Brands by name

Popular brands

Datex-Ohmeda 7100, Technical Reference Manual

Search results

Summary of Contents for 7100

Reviews:

Related manuals for 7100

Brands by name

Popular brands