manualshive.com logo in svg

Datex-Ohmeda 7100, Technical Reference Manual

Share
Download
Datex-Ohmeda 7100 Technical Reference Manual Download Page 48

7100 Anesthesia Ventilator

4-8

     02/03     1006-0836-000

4.7 User Settings

In normal operation, the user can set several parameters to a personal 
preference or to compensate for the surrounding influences. The range of some 
of these settings can vary from machine to machine.

The 

User Settings

 menu is used to adjust the range to normalized values.

4.7.1 Screen Contrast

The range from minimum to maximum screen contrast varies for individual 
displays. The 

Screen Contrast

 menu is used to tailor the range so that the 

screen image is still visible at minimum and maximum contrast settings for the 
user.

Remarks

The “Minimum Screen Contrast” and the “Maximum Screen Contrast” settings 
set the range of contrast values for the operator.

The “Optimal Screen Contrast” setting sets the default value.

Summary of Contents for 7100































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands