Datex-Ohmeda 7100 Technical Reference Manual Download Page 72

Page: 72 / 158

7100 Anesthesia Ventilator

4-32

02/03 1006-0836-000

4.10.8

Test Serial Port

The

Test Serial Port

menu includes directions for two tests.

•

External Serial Port Testing

: The external test requires that you

jumper pins 6 and 13 of the serial connector.

•

Internal Serial Port Testing

: The internal test does not require any

setup; it only tests serial port related components on the control
board.

Each test routine sets up the serial port circuits so transmit data is echoed
directly back to the receive circuits. The test fails if the data sent out is not
equal to the data received.

Remarks

If only the internal test fails, replace the control board.

If both tests fail:

•

Check the harness connections between the control board and the
Serial board (SAB/SICB).

•

Check the ribbon cable between the SAB and the external connector.

•

Replace the SAB/SCIB.

Summary of Contents for 7100






























































































































































Search results

Summary of Contents for 7100

Reviews:

Related manuals for 7100

Brands by name

Popular brands

Datex-Ohmeda 7100, Technical Reference Manual

Search results

Summary of Contents for 7100

Reviews:

Related manuals for 7100

Brands by name

Popular brands