Datalogic QuickScan Lite QW2400 Product Reference Manual Download

Page: 88 / 288

Enter/Exit Programming Mode

Case Conversion

QuickScan™ Lite QW2400

Case Conversion

This feature allows conversion of the case of all alphabetic characters to upper

or lower case.

Character Conversion

Character conversion is an eight byte configuration item. The eight bytes are 4

character pairs represented in hexadecimal ASCII values. The first character in

the pair is the character that will be converted. The second character in the pair

is the character to convert to. If the character to convert in a pair is FF, then no

conversion is done. See

"Character Conversion"

on page 252 for more detailed

programming instructions.

NOTE

Case conversion affects ONLY scanned bar code data, and does not affect
Label ID, Prefix, Suffix, or other appended data.

$CLFCA00



Case Conversion = Disable (no case conversion)

$CLFCA01



Case Conversion = Convert to upper case

$CLFCA02



Case Conversion = Convert to lower case

DEFAULT

$CLFCH

Configure Character Conversion

Summary of Contents for QuickScan Lite QW2400

































































































































































































































































































Search results

Summary of Contents for QuickScan Lite QW2400

Reviews:

Related manuals for QuickScan Lite QW2400

Brands by name

Popular brands

Datalogic QuickScan Lite QW2400, Product Reference Manual

Search results

Summary of Contents for QuickScan Lite QW2400

Reviews:

Related manuals for QuickScan Lite QW2400

Brands by name

Popular brands