Datalogic QuickScan Lite QW2400 Product Reference Manual Download

Page: 75 / 288

Product Reference Guide

USB-OEM Interface

Introduction

Feature settings for USB interfaces differ depending upon which host type the

scanner will be connected with. Use the feature settings in this chapter to spe-

cifically configure for the USB-OEM interface. Other USB interfaces are included

in the appropriate chapter for their host type.

Standard Factory Settings

Reference

Appendix B,

for a listing of standard factory settings.

Summary of Contents for QuickScan Lite QW2400

































































































































































































































































































Search results

Summary of Contents for QuickScan Lite QW2400

Reviews:

Related manuals for QuickScan Lite QW2400

Brands by name

Popular brands

Datalogic QuickScan Lite QW2400, Product Reference Manual

Search results

Summary of Contents for QuickScan Lite QW2400

Reviews:

Related manuals for QuickScan Lite QW2400

Brands by name

Popular brands