DataCard CP60 Printer Manual Download Page 19

Page: 19 / 134

Page 14

After it is printed, remove the card from the output hopper.

Tips for success

•

Allow 30 to 60 seconds for the printer to begin printing the test card.

•

The status light will flash green while the printer is processing the data.

•

If the status light is steady amber and the printer beeps, the printer is paused. Press the Ready key once to
un-pause the printer.

•

If the printer test card did not print successfully, try the procedure again, making sure you follow the
instructions. If the test card does not print, or if the printer does not initialize, contact your service provider.

•

The test card has the pattern shown. (The pattern will be monochrome dots, not colored dots, if the printer
uses a monochrome ribbon.)

Summary of Contents for CP60







































































































































Search results

Summary of Contents for CP60

Reviews:

Related manuals for CP60

Brands by name

Popular brands

DataCard CP60, Printer Manual

Search results

Summary of Contents for CP60

Reviews:

Related manuals for CP60

Brands by name

Popular brands