DataCard CP60 Printer Manual Download Page 120

Page: 120 / 134

Page 115

SC-01804 No Smart Card

The smart card module is not installed or detected.

Possible Cause 1:

Smart card data was sent to the printer and a smart card

module is not installed.

Solution 1:

Remove the smart card components of the card design. Print

cards without sending smart card data to the printer.

Possible Cause 2:

The smart card module is not communicating with the

rest of the printer.

Solution 2:

Check the printer to see whether a smart card module is

included in the printer. If it is, power the printer off and on (disconnect the
power cord from the printer power supply and then connect it again) so the
printer can detect the module when the printer powers up.

If a smart card module is part of the printer and you receive this message,

contact your service provider for assistance.

Related Topics:

"Features and options" on page 3

Summary of Contents for CP60







































































































































Search results

Summary of Contents for CP60

Reviews:

Related manuals for CP60

Brands by name

Popular brands

DataCard CP60, Printer Manual

Search results

Summary of Contents for CP60

Reviews:

Related manuals for CP60

Brands by name

Popular brands