DataCard CP60 Printer Manual Download

Page: 27 / 134

Page 22

Site requirements

Operating environment

•

Relative humidity: 20% to 80% non-condensing

•

Temperature: 60° F to 95° F (15° C to 35° C)

Electrical requirements

•

The power supply is rated at 100-240 VAC, 50-60
Hz, 1.8 amp. (It adjusts to any power within this
range.)

•

Single phase, 3-wire, grounded receptacle only.

Physical requirements

•

The printer weighs less than 11.5 pounds (5.3 kg).
The weight depends on the supplies and options
installed.

•

Printer dimensions are 21.5 inches (546 mm) long, and 7.8 inches (198 mm) wide. The 100-card input hopper
is 9.5 inches (241 mm) high and the 200-card hopper is 11.9 inches (302 mm) high.

•

The clearances required are 1 inch (25 mm) at the back, 2 inches (51 mm) on the left side, and 10.5 inches

(267 mm) above the printer latch to open the cover.

Summary of Contents for CP60







































































































































Search results

Summary of Contents for CP60

Reviews:

Related manuals for CP60

Brands by name

Popular brands

DataCard CP60, Printer Manual

Search results

Summary of Contents for CP60

Reviews:

Related manuals for CP60

Brands by name

Popular brands