Danfoss VLT HVAC Basic Drive FC 101, Programming Manual

Page: 45 / 104

[80] SL Digital
Output A See 13-52 SL Controller Action . The input
will go high whenever the Smart Logic
Action
[38] Set dig. out. A high is
executed. The input goes low whenever
the Smart Logic Action
[32] Set dig. out. A
low is executed.
[81] SL Digital
Output B See 13-52 SL Controller Action . The input
goes high whenever the Smart Logic
Action
[39] Set dig. out. B high is
executed. The input goes low whenever
the Smart Logic Action
[33] Set dig. out. B
low is executed.
[82] SL Digital
Output C See 13-52 SL Controller Action . The input
goes high whenever the Smart Logic
Action
[40] Set dig. out. C high is
executed. The input goes low whenever
the Smart Logic Action
[34] Set dig. out. C
low is executed.
[83] SL Digital
Output D See 13-52 SL Controller Action . The input
goes high whenever the Smart Logic
Action
[41] Set dig. out. D high is
executed. The input goes low whenever
the Smart Logic Action
[35] Set dig. out.
D low is executed.
[84] SL Digital
Output E See 13-52 SL Controller Action . The input
goes high whenever the Smart Logic
Action
[42] Set dig. out. E high is
executed. The input goes low whenever
the Smart Logic Action
[36] Set dig. out. E
low is executed.
[85] SL Digital
Output F See 13-52 SL Controller Action . The input
goes high whenever the Smart Logic
Action
[43] Set dig. out. F high is
executed. The input goes low whenever
the Smart Logic Action
[37] Set dig. out. F
low is executed.
[160] No alarm The output is high when no alarm is
present.
[161] Running reverse The output is high when the frequency
converter runs counter clockwise (the
logical product of the status bits
‘running’ AND ‘reverse’).
[165] Local reference
active
The output is high when 3-13 Reference
Site = [2] Local or when 3-13 Reference
Site = [0] Linked to hand auto at the
same time as the LCP is in [Hand On]
mode.
[166] Remote
reference active
The output is high when 3-13 Reference
Site [1] or Linked to hand/auto [0] while
the LCP is in [Auto on] mode.
[167] Start command
active
The output is high when there is an
active Start command (i.e. via digital
input bus connection or [Hand on] or
[Auto on], and no Stop command is
active.
[168] Drive in hand
mode
The output is high when the frequency
converter is in Hand on mode (as
indicated by the LED light above [Hand
on].
[169] Drive in auto
mode
The output is high when the frequency
converter is in Hand on mode (as
indicated by the LED light above [Auto
on].
[180] Clock Fault The clock function has been reset to
default (2000-01-01) because of a power
failure.
[181] Preventive
Maintenance
One or more of the Preventive
Maintenance Events programmed in
23-10 Maintenance Item has passed the
time for the specified action in
23-11 Maintenance Action .
[193] Sleep Mode The frequency converter/system has
turned into sleep mode. See parameter
group
22-4* Sleep Mode .
[194] Broken Belt A Broken Belt condition has been
detected. This function must be enabled
in
22-60 Broken Belt Function .
[196] Fire Mode The frequency converter is operating in
Fire Mode. See parameter group
24-0*
Fire Mode .
5-33 Term X30/7 Digi Out (MCB 101)
Option: Function:
[0]
*
No
operation This parameter is active when option module
MCB 101 is mounted in the frequency
converter. Same options and functions as
parameter group
5-3* Digital Outputs .
5-34 On delay, Terminal 42 Digital Output
Range: Function:
0.01 s
*
[0.00-600.00 s]
5-35 Off delay, Terminal 42 Digital Output
Range: Function:
0.01 s
*
[0.00-600.00 s]
3.6.4 5-4* Relays
Parameters for configuring the timing and the output
functions for the relays.
5-40 Function Relay
Array (Relay 1 [0], Relay 2 [1])
Select options to define the function of the relays.
The selection of each mechanical relay is realised in an array
parameter.
Option: Function:
[0] No operation Default for both relays
[1] Control Ready Control board receives supply voltage.
[2] Drive ready Frequency converter is ready for
operation and applies supply signal on
control board.
Parameters
VLT
®
HVAC Basic Drive FC 101 Programming Guide
MG18B302 - Rev. 2013-09-02 43
3 3