manualshive.com logo in svg

Daikin Super Multi Plus D-Series, Service Manual

Share
Download
Daikin Super Multi Plus D-Series Service Manual Download Page 270

SiEBE18-526

Troubleshooting for RA Indoor Unit

Troubleshooting

259

Troubleshooting

Check No.06

Refer to P.266

NO

NO

NO

Check No. 06

Indoor unit heat exchanger
thermistor check

Check the intake air filter.

Check the air passage.

YES

YES

(R4695)

Check the dust accumulation on 
the indoor unit heat exchanger.

YES

YES

Is there any 

short-circuit?

Is it very dirty?

Is it very dirty?

Does it conform to 

the thermistor characteristic

chart?

NO

Provide sufficient air passage.

Clean the air filter.

Clean the heat exchanger.

Replace the indoor unit PCB.

Replace the thermistor
(replace the indoor unit PCB).

Caution

Be sure to turn off power switch before connect or disconnect connector, 
or parts damage may be occurred.

Summary of Contents for Super Multi Plus D-Series












































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands