CYBEX CardioTouch 770T Service Manual Download Page 10 | Manualshive

Page: 10 / 261

background image

Emergency Stop Key (e-stop)

The e-stop key functions as an emergency stop. In an emergency situation, the e-stop key disengages
from the console and the treadmill will come to a stop. Before using the treadmill, clip the e-stop key as
described below.

1.

Compress the spring and clip the e-stop clamp to your clothing.
Ensure the clip engages enough clothing so it does not fall off in an emergency situation. Be sure
the string is free of knots and has enough slack for you to workout comfortably with the e-stop key
in place.

Qty.

Description

Item

1

Clothing

1

1

Clip

2

2.

Without falling off the treadmill, carefully step backward until the e-stop pulls out of the console.
If the e-stop clip falls off your clothing then the test has failed. Reclip the e-stop clip to your clothing
and repeat this step.

3.

Replace the e-stop key.

4.

The treadmill is now ready to be used. Ensure the e-stop clip is secured to your clothing at all times
during use.

Page 10 of 261

Cybex 770T/790T Treadmill Part Number

«
...
8
9
10
11
12
...
»

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Related manuals for CardioTouch 770T

Brand: OMCA Pages: 36

Brand: Salford Pages: 64

Brand: dbx Pages: 12

Brand: dbx Pages: 13

Brand: dbx Pages: 72

Brand: dbx Pages: 11

Brand: dbx Pages: 16

Brand: DBX Bushido Pages: 12

ST70 Instrument

Brand: Raymarine Pages: 12

Brand: Raven Pages: 73

Brand: Tascam Pages: 3

Brand: RAB Lighting Pages: 4

Brand: campgo Pages: 33

Brand: Össur Pages: 98

Flex Foot Cheetah

Brand: Össur Pages: 107

Brand: Össur Pages: 38

Brand: Össur Pages: 39

Bionic Symbionic Leg

Brand: Össur Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands