manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 142

Install top steps

1.

Install right top step by placing in position and inserting a long 3/8” drive socket extension into top
step.

Qty.

Description

Item

1

3/8” Drive Socket Exten-

sion

1

1

Right Top Step

2

2.

Pry the long 3/8” drive socket extension forwards to secure right top step.

3.

Repeat steps 1 and 2 for left top step.

Install end caps

1.

Install two screws securing right end cap using a Phillips screwdriver.

Qty.

Description

Item

2

Screws

1

1

Right end cap

2

2.

Repeat step for left end cap.

Center and tension the running belt

1.

Plug the power cord into the power outlet.

2.

Turn the main power switch to the on (I) position.

3.

Tap the

Quick Start

icon.

4.

Press the

Speed +

key to bring the speed up to 5 mph (8 kph). Allow the treadmill to run for a minute.

The lateral position of the running belt is correctly centered when the Cybex logo is centered between
the inside edges of the two belt tracking slots. If the Cybex logo is not centered between the belt
tracking slots, center the running belt with the following procedure.

Page 142 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands