manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 68

Setup menu

Select distance units.

Miles

or

Km

(Kilometers). Select weight units.

Lbs.

(Pounds),

Kg.

(Kilograms) or

Stone

(Stones).

Units

Perform Touch Calibration, Network Setup, or Channel Setup. See

A/V

Configuration

.

A/V Config

Set Default and Max workout times. Default choices are 20, 30, or 60 minutes.
Max choices are 20, 30, 60, or OFF.

Workout times

Set Min Speed, Max Speed, and Max Incline.

Limits

Set Pause time. Choices are OFF, 0:30, 1:00, or 2:00 minutes.

Pause

Select console beeper settings. Choices are ON, Some, or OFF.
Selecting Some enables beeper for safety related notifications, such as En-
tering Active, Exiting Active, and Cool Down.

Sound

Select default language to display on CardioTouch screen. Toolbox is only
available in English. Include Optional Languages. Select optional languages
to display on CardioTouch screen. Choices are

Include

or

Off

.

Language

Statistics

1.

Tap the

Statistics

icon to display the

Treadmill Totals

icon.

Page 68 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands