CYBEX CardioTouch 770T Service Manual Download Page 50

Page: 50 / 261

E3 View Monitor Controls

The CardioTouch screen is used to perform all setup operations for the E3 View Monitor.

CardioTouch screen functions

Return to

Toolbox

home

Wrench Icon

Go to

Setup

home screen

Moves forward in

Setup

menu to next screen

Next

Select TV + Data, TV Only or Data Only

Default Display Mode

Turn the E3 View Monitor on or off

On/Off

Reset the setup values and clear all pro-
grammed channels.

Reset Defaults

List all available channels

CH List

Toggles the setup menu

Setup

Navigate up through the on-screen menu

Navigate up

Navigate down through the on-screen menu

Navigate down

Decrease value

Navigate left

Page 50 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Search results

Summary of Contents for CardioTouch 770T

Reviews:

Related manuals for CardioTouch 770T

Brands by name

Popular brands

CYBEX CardioTouch 770T, Service Manual

Search results

Summary of Contents for CardioTouch 770T

Reviews:

Related manuals for CardioTouch 770T

Brands by name

Popular brands