CYBEX CardioTouch 770T Service Manual Download Page 117 | Manualshive

Page: 117 / 261

background image

4.

Unzip file to a folder on PC.
Zip file contains the following files:
• Folder labeled “boot”
• Empty text file with model name of product
• Other single files

Example of folder contents

5.

Copy the “boot” folder and other files to USB stick.
DO NOT copy zip file to USB stick.

6.

Perform both procedures for internal and external USB ports.

Install software through internal USB port

1.

Toggle the on/off (I/O) power switch to the off (O) position. The on/off (I/O) power switch is located
under the front end of the unit, or on the front right side panel.

Page 117 of 261

Cybex 770T/790T Treadmill Part Number

«
...
115
116
117
118
119
...
»

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Related manuals for CardioTouch 770T

Brand: UFO Pages: 16

Brand: Tascam Pages: 8

Brand: B-K lighting Pages: 5

Brand: B-K lighting Pages: 4

Brand: B-K lighting Pages: 3

Brand: Baker Pages: 82

Brand: Handler Pages: 25

Brand: Wahl Pages: 47

Brand: Datavideo Pages: 28

Brand: EAW Pages: 2

Brand: abc Pages: 28

Brand: unios Pages: 2

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brand: Lafayette Pages: 2

ProFire Lightbridge

Brand: M-Audio Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands