CYBEX CardioTouch 770T Service Manual Download Page 26

Page: 26 / 261

Description

Control Name

Control

Adjust

Volume

down.

VOLUME DOWN

A/V - Channel

CHANNEL UP

A/V - Channel

DOWN

CHANNEL DOWN

Press

STOP

once to end the workout session

and start the

Workout Review

. Press

STOP

again to exit to

Dormant Mode

STOP

Default speed is

OFF

during active mode.

Press the

FAN

key to control fan speed.

Choices are OFF, LOW and HI.

FAN

CardioTouch Symbols Used

Description

Icon Name

Icon

Quick Start

enters

Active Mode

at the default settings

with time counting up from 0:00.

Quick Start

Tap

Workouts

icon to enter workout group selection.

WORKOUTS

Tap

icon to enter TV control menu. If TV is not con-

nected, icon will not be shown.

Tap

TV + FM

icon to enter TV + FM control menu. If TV

+ FM is not connected, icon will not be shown.

TV + FM

Return to opening screen.

HOME

Enter

Active Mode

START

Page 26 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Search results

Summary of Contents for CardioTouch 770T

Reviews:

Related manuals for CardioTouch 770T

Brands by name

Popular brands

CYBEX CardioTouch 770T, Service Manual

Search results

Summary of Contents for CardioTouch 770T

Reviews:

Related manuals for CardioTouch 770T

Brands by name

Popular brands