manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 217

Remove wireless heart rate board

The wireless heart rate board is installed with double sided tape. Remove only if replacing with a new
wireless heart rate board.

1.

Unplug the wireless heart rate cable by un-latching connector from the wireless heart rate board.

Qty.

Description

Item

1

Wireless Heart Rate Cable

1

1

Wireless Heart Rate Board

2

2.

Pry the wireless heart rate board from the console using a flat head screwdriver.

3.

Clean any remaining double sided tape from the console.

Install wireless heart rate board

1.

Locate the new wireless heart rate board.

2.

Peel the backing from the double sided tape and place the wireless heart rate board in position on
the console.

Qty.

Description

Item

1

Wireless Heart Rate Cable

1

1

Wireless Heart Rate Board

2

3.

Plug the wireless heart rate cable into the wireless heart rate board.

Install back cover

Install the four screws securing the back cover to the console assembly using a Phillips screwdriver.

Page 217 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands