manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

The CYBEX CardioTouch 770T is a high-performance treadmill designed for intense cardio workouts. Ensure a seamless setup with the comprehensive Installation Instructions Manual, available for free download on our website. Get all the details you need to maximize your fitness routine and achieve your goals.

Share
Download
background image

Remove display board

Repairs and Service. Do not damage the wires or connectors when installing
or removing cables.

1.

Disconnect the display board cable from the MCC board connector (J16).

a) Press in the top of the cable connector.

Qty.

Description

Item

1

DO NOT PULL CONNEC-

TOR OUT BY THE WIRES!

1

1

Step a, Latch

2

1

Step b

3

1

Step c

4

b) Ensure latch disengages the connector.
c) Unplug cable by holding down latch and pulling straight out from connector. Do not pull on wires,

remove by connector.

2.

Remove the four screws securing the display board to the console assembly using a Phillips
screwdriver.

Qty.

Description

Item

1

Console Assembly

1

1

Display Board Connector

2

1

Display Board

3

4

Display Board Screw

4

Page 202 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Related manuals for CardioTouch 770T

DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Brand: DARKSTAR TECHNOLOGIES Pages: 4
TDW D2000 Maintenance Manuallines preview
D2000
Brand: TDW Pages: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Brand: Taurus Pages: 25
Vancare G Series Quick Reference Manual preview
G Series
Brand: Vancare Pages: 3
Paitec ES-2000 User Manual preview
ES-2000
Brand: Paitec Pages: 14
NEILPRYDE X1 Manual preview
X1
Brand: NEILPRYDE Pages: 53
JAC PRO+ Translation Of Original User Instructions preview
PRO+
Brand: JAC Pages: 103
3Disc Heron IOS Quick Start Manual preview
Heron IOS
Brand: 3Disc Pages: 12
JB-Lighting P4 Operating Instructions Manual preview
P4
Brand: JB-Lighting Pages: 60
ParaBody 858 Assembly Instruction Sheet preview
858
Brand: ParaBody Pages: 5
Jackson DISHSTAR ADA-SEER Operation Manual preview
DISHSTAR ADA-SEER
Brand: Jackson Pages: 2
Konica Minolta DF-619 Service Manual preview
DF-619
Brand: Konica Minolta Pages: 32
unios Echo Quick Installation Manual preview
Echo
Brand: unios Pages: 2
Nektar Panorama P1 User Manual preview
Panorama P1
Brand: Nektar Pages: 12
Parkside PFMR 1400 A1 Original Operating Instructions preview
PFMR 1400 A1
Brand: Parkside Pages: 58
Quincy QR-25 Series Manual preview
QR-25 Series
Brand: Quincy Pages: 31
Quidel Lyme FIA Sofia 2 User Manual preview
Lyme FIA Sofia 2
Brand: Quidel Pages: 49
Quest Leisure Products Versailles Instructions Manual preview
Versailles
Brand: Quest Leisure Products Pages: 12

Brands by name

Popular brands

Load more brands