manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 91

Error 11: Motion Sensor Defective

Cause:

The motion sensor is reading a consistent value indicative of being unplugged (650-750), or the ground
removed (2100-2900), or power is removed (550-600), or > 3500 (defective) for 10 minutes or greater
while in Opening Screen. Display initiates Dormant from Opening Screen. In Dormant, the GUI shows
a pop-up message indicating the user must touch the screen to begin, and that the motion sensor is
defective.

Use of the motion sensor is disabled outside of Active Mode. Console stores a single Error 11 at the
onset of this condition ONLY. Treadmill is otherwise fully functional.

Service:

• Check the motion sensor cable and connections for damage and replace as needed.
• Read the output value of the motion sensor in Diagnostics to determine the most likely type of failure

(see symptoms above.)

• Test the voltages at the motion sensor connection on the MCC. If OK, replace the motion sensor. If

voltages are inconsistent, replace the MCC and the motion sensor.

Page 91 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands