manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 164

Remove top steps

1.

Remove the right top step by inserting a long 3/8” drive socket extension into the right top step and
prying backwards.

Qty.

Description

Item

1

3/8” Drive Socket Exten-

sion

1

1

Right Top Step

2

2.

Remove right top step.

3.

Repeat steps 1 and 2 for left top step.

Loosen rear roller

Loosen the rear roller mounting bolts using a 3/4” Socket wrench.

Remove front roller

1.

Loosen the left mounting bolt using a 9/16” Socket wrench.

Qty.

Description

Item

1

Front roller

1

1

Drive belt

2

1

Mounting bolt

3

1

Tensioning slot

4

2.

Loosen the right mounting bolt using a 9/16” Socket wrench.

3.

Remove both mounting bolts.

4.

Slide the drive belt off of the front roller and remove the front roller.

Remove drive belt

Remove the drive belt off of the drive motor pulley.

Install drive belt

Install the drive belt into the grooves on the drive motor pulley.

Page 164 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands