CYBEX CardioTouch 770T Service Manual Download Page 180 | Manualshive

Page: 180 / 261

background image

Install motor cover

1.

Place the motor cover into position vertically by aligning the two tabs and four plastic connectors.
Two plastic connectors are mounted in the front cover and two in the motor cover. If motor cover
top does not fit properly, loosen the side screws as needed.

Qty.

Description

Item

1

Motor Cover

1

1

Front Cover

2

2

Screws

3

4

Plastic Connectors

4

2.

Tighten the two front cover screws using a Phillips screwdriver.
Be sure the screws are securing the motor cover's tabs.

Complete installation

1.

Plug the power cord into the power outlet.

2.

Verify the power cord is not being pinched under the front of the treadmill.

3.

Operate the unit at all levels to verify proper operation.

Power Cord

Tools Required:

• Phillips screwdriver

Disconnect power source

1.

Toggle the on/off (I/O) power switch to the off (O) position. The on/off (I/O) power switch is located
under the front end of the unit, or on the front right side panel.

2.

Unplug the treadmill from the power outlet.

Shock and electrocution hazard.
• Unplug unit and let sit 10 minutes before cleaning or performing

maintenance.

• Electrical charge can remain in unit after unplugging.
• Keep water and liquids away from electrical parts.

Page 180 of 261

Cybex 770T/790T Treadmill Part Number

«
...
178
179
180
181
182
...
»

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Related manuals for CardioTouch 770T

Brand: THORLABS Pages: 44

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: NEC Pages: 54

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: Idmed Pages: 2

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brand: Raytec Pages: 60

Brand: Abbott Pages: 64

Brand: Gako Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands