CYBEX CardioTouch 770T Service Manual Download Page 235

Page: 235 / 261

Install eight screws securing handset assembly to console using a Phillips screwdriver.

Qty.

Description

Item

Handset assembly

Console

Screw

Complete installation

Plug the power cord into the power outlet.

Verify the power cord is not being pinched under the front of the treadmill.

Operate the unit at all levels to verify proper operation.

iPod Cable

Tools Required:

• Phillips screwdriver
• ESD (Electrostatic Discharge) grounding strap

Disconnect power source

Unplug the power cord from the power outlet.

Shock and electrocution hazard.
• Unplug unit and let sit 10 minutes before cleaning or performing

maintenance.

• Electrical charge can remain in unit after unplugging.
• Keep water and liquids away from electrical parts.

Page 235 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Search results

Summary of Contents for CardioTouch 770T

Reviews:

Related manuals for CardioTouch 770T

Brands by name

Popular brands

CYBEX CardioTouch 770T, Service Manual

Search results

Summary of Contents for CardioTouch 770T

Reviews:

Related manuals for CardioTouch 770T

Brands by name

Popular brands