manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 40

Adjust sound volumes

After completing the channel setup, it may be necessary to adjust the volume level of each TV so they
all have similar volume levels.

1.

Plug headphones into headphone jack.

2.

Press the

TV

icon.

3.

Tap

Up

or

Down

to select a TV station.

4.

Adjust the volume of each TV to match each other using the TV’s remote control.
The goal is for a volume setting of 10 on the unit to be the same for all TV's.

5.

Repeat procedure for all TV's.

Using the Cybex Wireless Audio Receiver

1.

Plug headphones into headphone jack.

2.

Tap the TV icon to listen to TV channels.

3.

Tap

Up

or

Down

to change TV channels.

4.

Tap volume

Up

or

Down

to adjust volume.

Setup Complete

Personal TV Setup

The personal TV configuration uses a TV on a stand in front of the equipment.

Install coax cable filter (Treadmill only)

1.

Turn the Broadcast Vision television off.

Page 40 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands