manualshive.com logo in svg

CYBEX CardioTouch 770T, Service Manual

Share
Download
CYBEX CardioTouch 770T Service Manual Download Page 128

2.

Install the bolt, washer, bushing and rear roller nut for each side of the roller into position.

Qty.

Description

Item

1

Rear roller nut

1

1

Rear roller

2

1

Bushing

3

1

Washer

4

1

Bolt

5

3.

Tighten the two rear roller bolts using a 3/4” Socket wrench.
Tighten each bolt evenly, making sure not to tighten either bolt too many turns before moving to the
other bolt.

4.

Continue to tighten bolts until the front roller is all the way back in the tensioning slots.

5.

Tighten the front roller bolts using a 9/16” Socket wrench.

Install top steps

1.

Install right top step by placing in position and inserting a long 3/8” drive socket extension into top
step.

Qty.

Description

Item

1

3/8” Drive Socket Exten-

sion

1

1

Right Top Step

2

2.

Pry the long 3/8” drive socket extension forwards to secure right top step.

3.

Repeat steps 1 and 2 for left top step.

Page 128 of 261

Cybex 770T/790T Treadmill Part Number

Summary of Contents for CardioTouch 770T






































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands