background image

5

Conventions

The following conventions apply to the present installation and operating 

instructions:
– 

Steps to be carried out

 (operational sequence) are preceded by a “

” 

bullet.

–  This symbol identifies 

safety and danger instructions

 which, if dis-

regarded,  could  result  in  personal  injury  and/or  damage  to  material 

assets.

–  This symbol identifies additional 

information and instructions

 designed 

to assist you in handling your hybrid humidifier and ensure a proper and 

economical operation.

Safekeeping

Please keep these installation and operating instructions in a safe place 

where they are always available. If ownership changes, they must be passed 

on to the new operator.

If this documentation gets misplaced, please contact your Condair supplier 

to obtain immediate replacement.

Language versions

The installation and operating instructions for the Condair Dual Hybrid Humidi-

fier are avail able in several languages. Please contact your Condair supplier 

if you re quire another language version of the present documentation.

1.3 

Special tools

Important! 

Fastening the outer left and right vertical sections to the cross 

arms of the post-evaporation unit requires a 5 mm hexagon socket extension 

with a length of at least 230 mm (not included in the delivery).

min. 230 mm

ø14 mm

5 mm

Summary of Contents for Dual 2

















































































Reviews: